View HT36FA_375124.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

HT36FA Music Synthesizer 8-Bit MCU
Technical Document
* Tools Information * FAQs * Application Note
Features
* Operating voltage: 2.4V~5.0V * Operating frequency: * Stereo 16-bit DAC * Oscillation modes: XTAL/RCOSC * Low voltage reset * Eight-level subroutine nesting * Supports 8-bit table read instruction (TBLP) * HALT function and wake-up feature reduce power
Xtal: 6MHz~8MHz ROSC: typ. 6MHz
* Built-in 128K16-bit (2M-bit) ROM for program/data
shared
* Built-in 8 bit MCU with 2088 bits RAM * Two 8 bit programmable timer with 8 stage prescaler * 24 bidirectional I/O lines * Watchdog timer * Four polyphonic synthesizer
consumption
* Bit manipulation instructions * 63 powerful instructions * All instructions in 1 or 2 machine cycles * 20/32-pin SOP package
General Description
The HT36FA is an 8-bit high performance RISC architecture microcontroller specifically designed for various music applications. It provides an 8-bit MCU and a 4-channel Wavetable synthesizer. It has a built-in 8-bit microprocessor which controls the synthesizer to generate the melody by setting the special register. A HALT feature is provided to reduce power consumption.
Block Diagram
1 2 8 K 1 6 - b it ROM 8 - B it MCU 2088 RAM M u ltip lie r /P h a s e G e n e ra l 1 6 - B it DAC VD VS VD VS S DA SA D
PA0~PA7 PB0~PB7 PC 0~PC 7 OSC1 OSC2 RES
LCH RCH
Rev. 1.10
1
March 13, 2006
HT36FA
Pin Assignment
PB3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PB2 PB1 PB0 RCH LCH PB0 1 2 3 4 5 6 7 8 9 10 RCH VDDA VSSA OSC2 OSC1 VSS VDD RES PC7 20 19 18 17 16 15 14 13 12 11 H T36FA 2 0 S O P -A PB7 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PC0 VDDA VSSA OSC2 OSC1 VSS VDD RES PC6 PC5 PC4 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 H T36FA 3 2 S O P -A PB4 PB5 PB6 PB7 PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 PC0 PC1 PC2 PC3
Pad Assignment
PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PA7 PA6 24 PA5
RCH 1 2 3 4 LCH VDDA VSSA
33
32
31
30
29
28
27
26
25
23
(0 ,0 )
OSC2
5
OSC1 6 7 VSS
22 21 8 9 10 11 12 13 14 15 16 17 18 19 20
PA4 PA3 PA2
PC7
PC6
PC5
PC4
PC3
PC2
PC1
PC0
PA0
PA1
RES
Chip size: 2385 3225 (mm)2 * The IC substrate should be connected to VSS in the PCB layout artwork.
VDD
Rev. 1.10
2
March 13, 2006
HT36FA
Pad Coordinates
Pad No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 X -1003.950 -1003.950 -1003.950 -1003.950 -1042.350 -1042.350 -1052.100 -952.100 -236.026 -134.250 -23.650 76.350 186.950 286.950 397.550 497.550 608.150 Y 1463.950 1350.950 1238.510 1089.850 -587.774 -1265.626 -1439.900 -1439.900 -1448.750 -1448.750 -1448.750 -1448.750 -1448.750 -1448.750 -1448.750 -1448.750 -1448.750 Pad No. 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 X 708.150 818.750 1042.350 1042.350 1042.350 1041.900 941.900 831.300 731.300 620.700 520.700 410.100 310.100 199.500 99.500 -11.100 Y -1448.750 -1448.750 -1448.200 -1348.200 -1237.600 1462.150 1462.150 1462.150 1462.150 1462.150 1462.150 1462.150 1462.150 1462.150 1462.150 1462.150 Unit: mm
Pad Description
Pad No. 8, 7 3,4 18~25 Pad Name VDD, VSS VDDA, VSSA PA0~PA7 I/O 3/4 3/4 I/O Internal Connection 3/4 3/4 Wake-up, Pull-high or None Pull-high or None Pull-high or None 3/4 Xtal/Resistor 3/4 3/4 3/4 Function Digital power supply, ground DAC power supply Bidirectional 8-bit I/O port, wake-up by mask option
33~26 17~10 9 6 5 1 2
PB0~PB7 PC0~PC7 RESET OSC1 OSC2 RCH LCH
I/O I/O I I O O O
Bidirectional 8-bit I/O port Bidirectional 8-bit I/O port Reset input, active low XIN for Xtal or ROSCIN for resistor by mask option XOUT or T1 DAC output R channel DAC output L channel
Absolute Maximum Ratings
Supply Voltage ..........................VSS-0.3V to VSS+5.5V Input Voltage .............................VSS-0.3V to VDD+0.3V Storage Temperature ...........................-50C to 125C Operating Temperature ..........................-25C to 70C
Note: These are stress ratings only. Stresses exceeding the range specified under Absolute Maximum Ratings may cause substantial damage to the device. Functional operation of this device at other conditions beyond those listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Rev. 1.10
3
March 13, 2006
HT36FA
Electrical Characteristics
Symbol VDD IDD Parameter Operating Voltage Operating Current 4.5V ISTB 3V Standby Current 4.5V IOH 3V Flag Source Current 4.5V 3V Flag Sink Current 4.5V Input High Voltage for I/O Ports Input Low Voltage for I/O Ports 3/4 3/4 3/4 WDT enable (RC OSC) Test Conditions VDD 3/4 3V No load (OSC= 6MHz) Conditions 3/4 Min. 2.4 3/4 3/4 3/4 3/4 5 Typ. 4.5 2 8 1 1 3/4 Max. 5 8 mA 10 3/4 5 3/4 mA Ta=25C Unit V
mA
IOL VIH VIL
3/4 3/4 3/4
5 0.8VDD 0
3/4 3/4 3/4
3/4 VDD 0.2VDD
mA V V
Rev. 1.10
4
March 13, 2006
HT36FA
Function Description
Execution Flow The system clock for the HT36FA is derived from either a crystal or an RC oscillator. The oscillator frequency divided by 2 is the system clock for the MCU and it is internally divided into four non-overlapping clocks. One instruction cycle consists of four system clock cycles. Instruction fetching and execution are pipelined in such a way that a fetch takes one instruction cycle while decoding and execution takes the next instruction cycle. However, the pipelining scheme causes each instruction to effectively execute in one cycle. If an instruction changes the program counter, two cycles are required to complete the instruction. Program Counter - PC The 13-bit program counter (PC) controls the sequence in which the instructions stored in program ROM are executed and its contents specify a maximum of 8192 addresses for each bank. After accessing a program memory word to fetch an instruction code, the contents of the program counter are incremented by one. The program counter then points to the memory word containing the next instruction code.
S y s te m C lo c k o f M C U ( S y s te m C lo c k /2 ) PC T1 T2 T3 T4 T1
When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call, initial reset, internal interrupt, external interrupt or return from subroutine, the PC manipulates the program transfer by loading the address corresponding to each instruction. The conditional skip is activated by instruction. Once the condition is met, the next instruction, fetched during the current instruction execution, is discarded and a dummy cycle replaces it to retrieve the proper instruction. Otherwise proceed with the next instruction. The lower byte of the program counter (PCL) is a readable and writeable register (06H). Moving data into the PCL performs a short jump. The destination will be within 256 locations. Once a control transfer takes place, an additional dummy cycle is required. Program ROM HT36FA provides 18 address lines WA17~WA0 to read the Program ROM which is up to 2M bits, and is commonly used for the wavetable voice codes and the program memory. It provides two address types, one type is for program ROM, which is addressed by a bank pointer PF3~PF0 and a 13-bit program counter PC12~PC0;
T2 T3 T4 T1 T2 T3 T4
PC
PC+1
PC+2
F e tc h IN S T (P C ) E x e c u te IN S T (P C -1 )
F e tc h IN S T (P C + 1 ) E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 ) E x e c u te IN S T (P C + 1 )
Execution Flow Program Counter *16 *15 *14 *13 *12 *11 *10 *9 0 0 0 0 0 0 0 0 0 0 0 0 0 0 *8 0 0 0 *7 0 0 0 *6 0 0 0 *5 0 0 0 *4 0 0 0 *3 0 1 1 *2 0 0 1 *1 0 0 0 *0 0 0 0
Mode Initial Reset
Timer/Event Counter 0 Overflow PF3 PF2 PF1 PF0 0 Timer/Event Counter 1 Overflow PF3 PF2 PF1 PF0 0 Skip Loading PCL Jump, Call Branch Return From Subroutine
Program Counter+2 PF3 PF2 PF1 PF0 *12 *11 *10 *9 PF3 PF2 PF1 PF0 #12 #11 #10 #9 *8 @7 @6 @5 @4 @3 @2 @1 @0 #8 #7 #6 #5 #4 #3 #2 #1 #0
PF3 PF2 PF1 PF0 S12 S11 S10 S9 S8 S7 S6 S5 S4 S3 S2 S1 S0 Program Counter
Note:
*12~*0: Bits of Program Counter @7~@0: Bits of PCL #12~#0: Bits of Instruction Code
S12~S0: Bits of Stack Register @7~@0: Bits of PCL PF3~PF0: Bits of Bank Register 5 March 13, 2006
Rev. 1.10
HT36FA
and the other type is for wavetable code, which is addressed by the start address ST15~ST0. On the program type, WA17~WA0=PF3~PF0213+PC12~PC0. On t h e w a v e t abl e R O M t y p e , W A 1 7 ~W A 0 = ST15~ST025. Note: Program ROM address use word as address unit, but wavetable ROM address use BYTE as address unit.
0000H 0008H 000CH D e v ic e in itia liz a tio n p r o g r a m T im e r C o u n te r 0 in te r r u p t s u b r o u tin e T im e r C o u n te r 1 in te r r u p t s u b r o u tin e P ro g ra m M e m o ry
n00H nFFH
L o o k - u p ta b le ( 2 5 6 w o r d s )
Program Memory - ROM The program memory is used to store the program instructions which are to be executed. It also contains data, table, and interrupt entries, and is organized into 819216 bits, addressed by the bank pointer, program counter and table pointer. Certain locations in the program memory of each bank are reserved for special usage:
* Location 000H on bank0
1FFFH L o o k - u p ta b le ( 2 5 6 w o r d s ) 1 6 b its N o te : n ra n g e s fro m 0 0 to 1 F .
Program Memory for Each Bank the TBLH. The Table Higher-order byte register (TBLH) is read only. The Table Pointer (TBLP) is a read/write register (07H), which indicates the table location. Before accessing the table, the location must be placed in TBLP. The TBLH is read only and cannot be restored. If the main routine and the ISR (Interrupt Service Routine) both employ the table read instruction, the contents of the TBLH in the main routine are likely to be changed by the table read instruction used in the ISR. Errors can occur. In this case, using the table read instruction in the main routine and the ISR simultaneously should be avoided. However, if the table read instruction has to be applied in both the main routine and the ISR, the interrupt should be disabled prior to the table read instruction. It will not be enabled until the TBLH has been backed up. All table related instructions need 2 cycles to complete the operation. These areas may function as normal program memory depending upon user requirements.
* Bank pointer
This area is reserved for the initialization program. After chip reset, the program always begins execution at location 000H on bank0.
* Location 008H
This area is reserved for the Timer Counter 0 interrupt service program on each bank. If timer interrupt results from a timer counter 0 overflow, and if the interrupt is enabled and the stack is not full, the program begins execution at location 008H corresponding to its bank.
* Location 00CH
This area is reserved for the Timer Counter 1 interrupt service program on each bank. If a timer interrupt results from a Timer Counter 1 overflow, and if the interrupt is enabled and the stack is not full, the program begins execution at location 00CH corresponding to its bank.
* Table location
Any location in the ROM space can be used as look-up tables. The instructions TABRDC [m] (the current page, 1 page=256 words) and TABRDL [m] (the last page) transfer the contents of the lower-order byte to the specified data memory, and the higher-order byte to TBLH (08H). Only the destination of the lower-order byte in the table is well-defined, the higher-order byte of the table word are transferred to
The program memory is organized into 16 banks and each bank into 819216 bits of program ROM. PF3~PF0 is used as the bank pointer. After an instruction has been executed to write data to the PF register to select a different bank, note that the new bank will not be selected immediately. It is not until the following instruction has completed execution that the bank will be actually selected. It should be note that the PF register has to be cleared before setting to output mode. Table Location
Instruction (s) TABRDC [m] TABRDL [m]
*16
*15
*14
*13
*12
*11
*10
*9 P9 1
*8 P8 1
*7 @7 @7
*6 @6 @6
*5 @5 @5
*4 @4 @4
*3 @3 @3
*2 @2 @2
*1 @1 @1
*0 @0 @0
P16 P15 P14 P13 P12 P11 P10 P16 P15 P14 P13 1 1 1
Table Location Note: *16~*0: Bits of table location @7~@0: Bits of table pointer P16~P8: Bits of current Program Counter P16~P13: Bits of bank PF3~PF0
Rev. 1.10
6
March 13, 2006
HT36FA
Wavetable ROM The ST15~ST0 is used to defined the start address of each sample on the wavetable and read the waveform data from the location. HT36FA provides 18 output address lines from WA17~WA0, the ST15~ST0 is used to locate the major 13 bits i.e. WA17~WA5 and the undefined data from WA4~WA0 is always set to 00000b. So the start address of each sample have to be located at a multiple of 32. Otherwise, the sample will not be read out correctly because it has a wrong starting code. Stack Register - Stack This is a special part of the memory which is used to save the contents of the program counter only. The stack is organized into 8 levels and is neither part of the data nor part of the program space, and is neither readable nor writeable. The activated level is indexed by the stack pointer (SP) and is neither readable nor writeable. At a subroutine call or interrupt acknowledgment, the contents of the program counter are pushed onto the stack. At the end of a subroutine or an interrupt routine, signaled by a return instruction (RET or RETI), the program counter is restored to its previous value from the stack. After a chip reset, the SP will point to the top of the stack. If the stack is full and a non-masked interrupt takes place, the interrupt request flag will be recorded but the acknowledgment will be inhibited. When the stack pointer is decremented (by RET or RETI), the interrupt will be serviced. This feature prevents stack overflow allowing the programmer to use the structure more easily. In a similar case, if the stack is full and a CALL is subsequently executed, a stack overflow occurs and the first entry will be lost (only the most recent eight return address are stored). Data Memory - RAM The data memory is designed with 256 8 bits. The data memory is divided into three functional groups, namely; special function registers, wavetable function register and general purpose data memory (2088). Most of which are readable/writeable, although some are read only. The special function registers include the Indirect Addressing register 0 (00H), the Memory Pointer register 0 (MP0;01H), the Indirect Addressing register 1 (02H), the Memory Pointer register 1 (MP1;03H), the Accumulator (ACC;05H), the Program Counter Lower-byte register (PCL;06H), the Table Pointer (TBLP;07H), the Table Higher-order byte register (TBLH;08H), the Watchdog Timer option Setting register (WDTS;09H), the Status register (STATUS;0AH), the Interrupt Control register (INTC;0BH), the Timer Counter 0 Lower-order byte register (TMR0L;0DH), the Timer Counter 0 Control register (TMR0C;0EH), the Timer Counter 1 Lower-order byte register (TMR1L;10H), the Timer Counter 1 Control Rev. 1.10 7
00H 01H 02H 03H 04H 05H 06H 07H 08H 09H 0AH 0BH 0CH 0DH 0EH 0FH 10H 11H 12H 13H 14H 15H 16H 17H 18H 19H 1AH 1BH 1CH 1DH 1EH 1FH 20H 21H 22H 23H 24H 25H 26H 27H 28H 29H 2AH 2BH L e ft V o lu m e C o n tr o l ( L V C ) R ig h t V o lu m C o n tro l (R V C ) DAC DAC D AC Low PF H ig h B y te ( D A H ) B y te (D A L ) C o n tro l (D A C ) TM R1L TM R1C PA PAC PB PBC PC PCC TM R0L TM R0C S p e c ia l P u r p o s e D a ta M e m o ry ACC PCL TBLP TBLH W DTS STATUS IN T C In d ir e c t A d d r e s s in g R e g is te r 0 MP0 In d ir e c t A d d r e s s in g R e g is te r 1 MP1
C h a n n e l N u m b e r S e le c t ( C H A N )
F r e q u e n c y N u m b e r H ig h B y te ( F r e q N H ) F re q u e n c y N u m b e r L o w B y te (F re q N L )
S ta r t A d d r e s s H ig h B y te ( A d d r H ) S ta rt A d d re s s L o w B y te (A d d rL ) R e p e a t N u m b e r H ig h B y te ( R e H ) R e p e a t N u m b e r L o w B y te (R e L ) V o lu m e C o n tr o l H ig h ( E N V )
W a v e ta b le F u n c tio n R e g is te r
2FH 30H G e n e ra l P u rp o s e D a ta M e m o ry (2 0 8 B y te s ) FFH
:U nused, re a d a s "0 0 "
RAM Mapping register (TMR1C;11H), the I/O registers (PA;12H, PB;14H, PC;16H) and the I/O control registers (PAC;13H, PBC;15H, PCC;17H). The program ROM bank select (PF;1CH). The DAC High byte (DAH;1DH). The DAC low byte (DAL;1EH). The DAC control (DAC;1FH). The wavetable function registers is defined between 20H~2AH. The remaining space before the
March 13, 2006
HT36FA
30H is reserved for future expanded usage and reading these locations will return the result 00H. The general purpose data memory, addressed from 30H to FFH, is used for data and control information under instruction command. All data memory areas can handle arithmetic, logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the data memory can be set and reset by the SET [m].i and CLR [m].i instructions, respectively. They are also indirectly accessible through Memory pointer registers (MP0:01H, MP1:03H). Indirect Addressing Register Location 00H and 02H are indirect addressing registers that are not physically implemented. Any read/write operation of [00H] and [02H] access data memory pointed to by MP0 (01H) and MP1 (03H), respectively. Reading location 00H or 02H directly will return the result 00H. And writing directly results in no operation. The function of data movement between two indirect addressing registers, is not supported. The memory pointer registers, MP0 and MP1, are 8-bit register which can be used to access the data memory by combining corresponding indirect addressing registers. Accumulator The accumulator closely relates to ALU operations. It is mapped to location 05H of the data memory and it can operate with immediate data. The data movement between two data memory locations must pass through the accumulator. Arithmetic and Logic Unit - ALU This circuit performs 8-bit arithmetic and logic operation. The ALU provides the following functions:
* Arithmetic operations (ADD, ADC, SUB, SBC, DAA) * Logic operations (AND, OR, XOR, CPL) * Rotation (RL, RR, RLC, RRC) * Increment & Decrement (INC, DEC) * Branch decision (SZ, SNZ, SIZ, SDZ ....)
The ALU not only saves the results of a data operation but can also change the status register. Status Register - STATUS This 8-bit register (0AH) contains the zero flag (Z), carry flag (C), auxiliary carry flag (AC), overflow flag (OV), power down flag (PDF) and Watchdog time-out flag (TO). It also records the status information and controls the operation sequence. With the exception of the TO and PDF flags, bits in the status register can be altered by instructions like any other register. Any data written into the status register will not change the TO or PDF flags. In addition it should be noted that operations related to the status register may give different results from those intended. The TO and PDF flags can only be changed by system power up, Watchdog Timer overflow, executing the HALT instruction and clearing the Watchdog Timer. The Z, OV, AC and C flags generally reflect the status of the latest operations. In addition, on entering the interrupt sequence or executing a subroutine call, the status register will not be automatically pushed onto the stack. If the contents of status are important and the subroutine can corrupt the status register, the programmer must take precautions to save it properly. Interrupt The HT36FA provides two internal timer counter interrupts on each bank. The Interrupt Control register (INTC;0BH) contains the interrupt control bits that sets the enable/disable and the interrupt request flags. Once an interrupt subroutine is serviced, all other interrupts will be blocked (by clearing the EMI bit). This scheme may prevent any further interrupt nesting. Other Function
Bit No. 0
Label C
C is set if an operation results in a carry during an addition operation or if a borrow does not take place during a subtraction operation; otherwise C is cleared. Also it is affected by a rotate through carry instruction. AC is set if an operation results in a carry out of the low nibbles in addition or no borrow from the high nibble into the low nibble in subtraction; otherwise AC is cleared. Z is set if the result of an arithmetic or logical operation is zero; otherwise Z is cleared. OV is set if an operation results in a carry into the highest-order bit but not a carry out of the highest-order bit, or vice versa; otherwise OV is cleared. PDF is cleared by either a system power-up or executing the CLR WDT instruction. PDF is set by executing the HALT instruction. TO is cleared by a system power-up or executing the CLR WDT or HALT instruction. TO is set by a WDT time-out. Unused bit, read as 0 Status (0AH) Register
1 2 3 4 5 6~7
AC Z OV PDF TO 3/4
Rev. 1.10
8
March 13, 2006
HT36FA
interrupt requests may occur during this interval but only the interrupt request flag is recorded. If a certain interrupt needs servicing within the service routine, the programmer may set the EMI bit and the corresponding bit of the INTC to allow interrupt nesting. If the stack is full, the interrupt request will not be acknowledged, even if the related interrupt is enabled, until the SP is decremented. If immediate service is desired, the stack must be prevented from becoming full. All these kinds of interrupt have a wake-up capability. As an interrupt is serviced, a control transfer occurs by pushing the program counter onto the stack and then branching to subroutines at specified locations in the program memory. Only the program counter is pushed onto the stack. If the contents of the register and Status register (STATUS) are altered by the interrupt service program which may corrupt the desired control sequence, then the programmer must save the contents first. The internal Timer Counter 0 interrupt is initialized by setting the Timer Counter 0 interrupt request flag (T0F; bit 5 of INTC), caused by a Timer Counter 0 overflow. When the interrupt is enabled, and the stack is not full and the T0F bit is set, a subroutine call to location 08H will occur. The related interrupt request flag (T0F) will be reset and the EMI bit cleared to disable further interrupts. The Timer Counter 1 interrupt is operated in the same manner as Timer Counter 0. The related interrupt control bits ET1I and T1F of the Timer Counter 1 are bit 3 and bit 6 of the INTC, respectively. During the execution of an interrupt subroutine, other interrupt acknowledgments are held until the RETI instruction is executed or the EMI bit and the related interrupt control bit are set to 1 (if the stack is not full). To return from the interrupt subroutine, the RET or RETI instruction may be invoked. RETI will set the EMI bit to enable an interrupt service, but RET will not. Interrupts occurring in the interval between the rising edges of two consecutive T2 pulses, will be serviced on the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests the priorities in the following table apply. These can be Bit No. 0 1, 4, 7 2 3 5 6 Label EMI 3/4 ET0I ET1I T0F T1F masked by resetting the EMI bit. Interrupt Source Timer Counter 0 overflow Timer Counter 1 overflow Priority 1 2 Vector 08H 0CH
The Timer Counter 0/1 interrupt request flag (T0F/T1F), Enable Timer Counter 0/1 bit (ET0I/ET1I) and Enable Master Interrupt bit (EMI) constitute an interrupt control register (INTC) which is located at 0BH in the data memory. EMI, ET0I, ET1I are used to control the enabling/disabling of interrupts. These bits prevent the requested interrupt from being serviced. Once the interrupt request flags (T0F, T1F) are set, they will remain in the INTC register until the interrupts are serviced or cleared by a software instruction. It is recommended that a program does not use the CALL subroutine within the interrupt subroutine. Because interrupts often occur in an unpredictable manner or need to be serviced immediately in some applications, if only one stack is left and enabling the interrupt is not well controlled, once the CALL subroutine operates in the interrupt subroutine, it may damage the original control sequence. Oscillator Configuration The HT36FA provides two types of oscillator circuit for the system clock, i.e., RC oscillator and crystal oscillator. No matter what type of oscillator, the signal divided by 2 is used for the system clock. The HALT mode stops the system oscillator and ignores external signal to conserve power. If the RC oscillator is used, an external resistor between OSC1 and VSS is required. The system clock, divided by 4, is available on OSC2 with pull-high resistor, which can be used to synchronize external logic. The RC oscillator provides the most cost effective solution. However, the frequency of the oscillation may
OSC1 V
DD
OSC1
OSC2 C r y s ta l O s c illa to r
fS
YS
/8
RC
OSC2
O s c illa to r
System Oscillator Function
Controls the Master (Global) interrupt (1=enabled; 0=disabled) Unused bit, read as 0 Controls the Timer Counter 0 interrupt (1=enabled; 0=disabled) Controls the Timer Counter 1 interrupt (1=enabled; 0=disabled) Internal Timer Counter 0 request flag (1=active; 0=inactive) Internal Timer Counter 1 request flag (1=active; 0=inactive) INTC (0BH) Register
Rev. 1.10
9
March 13, 2006
HT36FA
vary with VDD, temperature, and the chip itself due to process variations. It is therefore, not suitable for timing sensitive operations where accurate oscillator frequency is desired. On the other hand, if the crystal oscillator is selected, a crystal across OSC1 and OSC2 is needed to provide the feedback and phase shift required for the oscillator, and no other external components are required. A resonator may be connected between OSC1 and OSC2 to replace the crystal and to get a frequency reference, but two external capacitors in OSC1 and OSC2 are required. The WDT oscillator is a free running on-chip RC oscillator, and no external components are required. Even if the system enters the Power Down Mode, the system clock is stopped, but the WDT oscillator still works with a period of approximately 78ms. The WDT oscillator can be disabled by mask option to conserve power. Watchdog Timer - WDT The WDT clock source is implemented by a dedicated RC oscillator (WDT oscillator) or instruction clock (system clock of the MCU divided by 4), determined by mask options. This timer is designed to prevent a software malfunction or sequence jumping to an unknown location with unpredictable results. The Watchdog Timer can be disabled by mask option. If the Watchdog Timer is disabled, all the executions related to the WDT result in no operation. Once the internal WDT oscillator (RC oscillator with a period of 78ms normally) is selected, it is first divided by 256 (8-stages) to get the nominal time-out period of approximately 20ms. This time-out period may vary with temperature, VDD and process variations. By invoking the WDT prescaler, longer time-out periods can be realized. Writing data to WS2, WS1, WS0 (bit 2,1,0 of the WDTS) can give different time-out periods. If WS2, WS1, WS0 all equal to 1, the division ratio is up to 1:128, and the maximum time-out period is 2.6 seconds. If the WDT oscillator is disabled, the WDT clock may still come from the instruction clock and operate in the same manner except that in the HALT state the WDT may stop counting and lose its protecting purpose. In this situation the logic can only be restarted by external logic. The high nibble and bit 3 of the WDTS are reserved for user defined flags, and the programmer may use these flags to indicate some specified status.
S y s te m C lo c k /8 M ask O p tio n S e le c t 8 - b it C o u n te r
WS2 0 0 0 0 1 1 1 1
WS1 0 0 1 1 0 0 1 1
WS0 0 1 0 1 0 1 0 1
Division Ratio 1:1 1:2 1:4 1:8 1:16 1:32 1:64 1:128
If the device operates in a noisy environment, using the on-chip RC oscillator (WDT OSC) is strongly recommended, since the HALT will stop the system clock. The WDT overflow under normal operation will initialize a chip reset and set the status bit TO. Whereas in the HALT mode, the overflow will initialize a warm reset only the Program Counter and SP are reset to zero. To clear the WDT contents (including the WDT prescaler ), 3 methods are implemented; external reset (a low level to RES), software instructions, or a HALT instruction. The software instructions include CLR WDT and the other set - CLR WDT1 and CLR WDT2. Of these two types of instructions, only one can be active depending on the mask option - CLR WDT times selection option. If the CLR WDT is selected (i.e. CLRWDT times equal one), any execution of the CLR WDT instruction will clear the WDT. In case CLR WDT1 and CLR WDT2 are chosen (i.e. CLRWDT times equal two), these two instructions must be executed to clear the WDT; otherwise, the WDT may reset the chip because of time-out. Power Down Operation - HALT The HALT mode is initialized by a HALT instruction and results in the following...
* The system oscillator will turn off but the WDT oscilla-
tor keeps running (If the WDT oscillator is selected). Watchdog Timer - WDT
* The contents of the on-chip RAM and registers remain
unchanged
* The WDT and WDT prescaler will be cleared and
starts to count again (if the clock comes from the WDT oscillator).
W D T P r e s c a le r 7 - b it C o u n te r
W DT OSC
8 -to -1 M U X W D T T im e - o u t
W S0~W S2
Watchdog Timer
Rev. 1.10
10
March 13, 2006
HT36FA
* All I/O ports maintain their original status. * The PDF flag is set and the TO flag is cleared. * The HALT pin will output a high level signal to disable
TO 0 u 0 1 1
PDF 0 u 1 u 1
RESET Conditions RES reset during power-up RES reset during normal operation RES wake-up HALT WDT time-out during normal operation WDT wake-up HALT
the external ROM. The system can leave the HALT mode by means of an external reset, an interrupt, an external falling edge signal on port A or a WDT overflow. An external reset causes a device initialization and the WDT overflow performs a warm reset. By examining the TO and PDF flags, the cause for a chip reset can be determined. The PDF flag is cleared when there is a system power-up or by executing the CLR WDT instruction and it is set when a HALT instruction is executed. The TO flag is set if the WDT time-out occurs, and causes a wake-up that only resets the Program Counter and SP, the others remain in their original status. The port A wake-up and interrupt methods can be considered as a continuation of normal execution. Each bit in port A can be independently selected to wake-up the device by mask option. Awakening from an I/O port stimulus, the program will resume execution of the next instruction. If awakening from an interrupt, two sequences may occur. If the related interrupts is disabled or the interrupts is enabled but the stack is full, the program will resume execution at the next instruction. If the interrupt is enabled and the stack is not full, a regular interrupt response takes place. Once a wake-up event occurs, it takes 1024 tSYS (system clock period) to resume to normal operation. In other words, a dummy cycle period will be inserted after the wake-up. If the wake-up results from an interrupt acknowledge, the actual interrupt subroutine will be delayed by one more cycle. If the wake-up results in next instruction execution, this will execute immediately after a dummy period has finished. If an interrupt request flag is set to 1 before entering the HALT mode, the wake-up function of the related interrupt will be disabled. To minimize power consumption, all I/O pins should be carefully managed before entering the HALT status. Reset There are 3 ways in which a reset can occur:
* RES reset during normal operation * RES reset during HALT * WDT time-out reset during normal operation
Note: u stands for unchanged To guarantee that the system oscillator has started and stabilized, the SST (System Start-up Timer) provides an extra-delay of 1024 system clock pulses during system power up or when the system awakes from a HALT state. When a system power-up occurs, the SST delay is added during the reset period. But when the reset comes from the RES pin, the SST delay is disabled. Any wake-up from HALT will enable the SST delay. The functional units chip reset status are shown below. Program Counter Interrupt Prescaler WDT Timer Counter (0/1) Input/output ports Stack Pointer
V
DD
000H Disable Clear Clear. After master reset, WDT begins counting Off Input mode Points to the top of stack
RES
Reset Circuit
VDD RES S S T T im e - o u t C h ip R e s e t tS
ST
Reset Timing Chart
HALT W DT W DT T im e - o u t R eset W a rm R eset
The WDT time-out during HALT is different from other chip reset conditions, since it can perform a warm re set that just resets the Program Counter and SP, leaving the other circuits to maintain their state. Some registers remain unchanged during any other reset conditions. Most registers are reset to the initial condition when the reset conditions are met. By examining the PDF and TO flags, the program can distinguish between different chip resets. Rev. 1.10 11
RES SST 1 0 -s ta g e R ip p le C o u n te r P o w e r - o n D e te c tin g C o ld R eset
OSCI
Reset Configuration March 13, 2006
HT36FA
The registers status is summarized in the following table: Register MP0 MP1 ACC Program Counter TBLP TBLH WDTS STATUS INTC TMR0L TMR0C TMR1L TMR1C PA PAC PB PBC PC PCC PF DAH DAL DAC CHAN FreqNH FreqNL AddrH AddrL ReH ReL ENV LVC RVC Note: Reset (Power-on) xxxx xxxx xxxx xxxx xxxx xxxx 0000H xxxx xxxx xxxx xxxx 0000 0111 --00 xxxx -00- 00-0 xxxx xxxx 00-0 1000 xxxx xxxx 00-0 1000 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 ---- 0000 xxxx xxxx xxxx xxxx ---- -000 00-- --00 xxxx xxxx xxxx xxxx xxxx xxxx xxxx xxxx x--x xxxx xxxx xxxx x-xx --xx xxxx xxxx xxxx xxxx * stands for warm reset u stands for unchanged x stands for unknown - stands for unused WDT Time-out (Normal Operation) uuuu uuuu uuuu uuuu uuuu uuuu 0000H uuuu uuuu uuuu uuuu 0000 0111 --1u uuuu -00- 00-0 uuuu uuuu 00-0 1000 uuuu uuuu 00-0 1000 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 ---- 0000 uuuu uuuu uuuu uuuu ---- -000 uu-- --uu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu u--u uuuu uuuu uuuu u-uu --uu uuuu uuuu uuuu uuuu RES Reset (Normal Operation) uuuu uuuu uuuu uuuu uuuu uuuu 0000H uuuu uuuu uuuu uuuu 0000 0111 --uu uuuu -00- 00-0 uuuu uuuu 00-0 1000 uuuu uuuu 00-0 1000 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 ---- 0000 uuuu uuuu uuuu uuuu ---- -000 uu-- --uu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu u--u uuuu uuuu uuuu u-uu --uu uuuu uuuu uuuu uuuu RES Reset (HALT) uuuu uuuu uuuu uuuu uuuu uuuu 0000H uuuu uuuu uuuu uuuu 0000 0111 --01 uuuu -00- 00-0 uuuu uuuu 00-0 1000 uuuu uuuu 00-0 1000 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 1111 ---- 0000 uuuu uuuu uuuu uuuu ---- -000 uu-- --uu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu u--u uuuu uuuu uuuu u-uu --uu uuuu uuuu uuuu uuuu WDT Time-out (HALT)* uuuu uuuu uuuu uuuu uuuu uuuu 0000H uuuu uuuu uuuu uuuu uuuu uuuu --11 uuuu -uu- uu-u uuuu uuuu uu-u 1uuu uuuu uuuu uu-u 1uuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu ---- uuuu uuuu uuuu uuuu uuuu ---- -uuu uu-- --uu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu u--u uuuu uuuu uuuu u-uu --uu uuuu uuuu uuuu uuuu
Rev. 1.10
12
March 13, 2006
HT36FA
Timer 0/1 Timer 0 is an 8-bit counter, and its clock source comes from the system clock divided by an 8-stage prescaler. There are two registers related to Timer 0; TMR0L (0DH) and TMR0C (0EH). One physical registers are mapped to TMR0L location; writing TMR0L makes the starting value be placed in the Timer 0 preload register and reading the TMR0 gets the contents of the Timer 0 counter. The TMR0C is a control register, which defines the division ration of the prescaler and counting enable or disable. Writing data to B2, B1 and B0 (bits 2, 1, 0 of TMR0C) can yield various clock sources. One the Timer 0 starts counting, it will count from the current contents in the counter to FFH. Once an overflow occurs, the counter is reloaded from a preload register, and generates an interrupt request flag (T0F; bit 2 of INTCH). To enable the counting operation, the timer On bit (TON; bit 4 of TMR0C) should be set to 1. For proper operation, bit 7 of TMR0C should be set to 1 and bit 3, bit 6 should be set to 0. There are two registers related to the Timer Counter1; TMR1L(10H), TMR1C(11H). The Timer Counter 1 operates in the same manner as Timer Counter 0. TMR0C/TMR1C B2 0 0 0 0 1 1 1 1 B1 0 0 1 1 0 0 1 1 B0 0 1 0 1 0 1 0 1 T0F SYS CLK/16 SYS CLK/32 SYS CLK/64 SYS CLK/128 SYS CLK/256 SYS CLK/512 SYS CLK/1024 SYS CLK/2048
S y s te m C lo c k /8 8 -s ta g e P r e s c a le r T0F TON T im e r 0 /1 O v e r flo w T im e r 0 /1 P r e lo a d R e g is te r D a ta B u s R e lo a d
Timer 0/1 Input/Output Ports There are 20 bidirectional input/output lines labeled from PA to PC0~3, which are mapped to the data memory of [12H], [14H], [16H], respectively. All these I/O ports can be used for input and output operations. For input operation, these ports are non-latching, that is, the inputs must be ready at the T2 rising edge of instruction MOV A,[m] (m=12H, 14H or 16H). For output operation, all data is latched and remains unchanged until the output latch is rewritten. Each I/O line has its own control register (PAC, PBC, PCC0~3) to control the input/output configuration. With this control register, CMOS output or Schmitt trigger input with or without pull-high resistor (mask option) structures can be reconfigured dynamically under software control. To function as an input, the corresponding latch of the control register must write a 1. The pull-high resistance will exhibit automatically if the pull-high option is selected. The input source also depends on the control register. If the control register bit is 1, input will read the pad state. If the control register bit is 0, the contents of the latches will move to the internal bus. The latter is possible in read-modify-write instruction. For output function, CMOS is the only configuration. These control registers are mapped to locations 13H, 15H and 17H. After a chip reset, these input/output lines remain at high levels or floating (mask option). Each bit of these input/output latches can be set or cleared by the SET [m].i or CLR [m].i (m=12H, 14H or 16H) instruction. Some instructions first input data and then follow the output operations. For example, the SET [m].i, CLR [m].i, CPL [m] and CPLA [m] instructions read the entire port states into the CPU, execute the defined operations (bit-operation), and then write the results back to the latches or the accumulator. Each line of port A has the capability to wake-up the device.
TMR0C Bit 4 to enable/disable timer counting (1=enable; 0=disable) TMR0C Bit 3, always write 0. TMR0C Bit 5, always write 0. TMR0C Bit 6, always write 0. TMR0C Bit 7, always write 1.
Rev. 1.10
13
March 13, 2006
HT36FA
D a ta B u s W r ite C o n tr o l R e g is te r C h ip R e s e t R e a d C o n tr o l R e g is te r D a ta B it Q D CK S Q M R e a d I/O S y s te m W a k e -U p U X C o n tr o l B it Q D V V CK S Q
DD
DD
W eak P u ll- u p M a s k O p tio n I/O L in e
W r ite I/O
Input/Output Ports Channel Wavetable Synthesizer Name 1DH 1EH Function DAC high byte (no default value) DAC low byte (no default value) DAON=1: DAC ON DAON=0: DAC OFF (default) SELW=1: DAC data from wavetable SELW=0: DAC data from MCU Channel number selection High byte frequency number Low byte frequency number High byte start address Low byte start address Wave bit select, High byte repeat number Low byte repeat number Envelope control, Volume control Left Volume control Right Volume control D7 DA15 DA7 3/4 VM BL3 FR7 ST15 ST7 WBS RE7 A_R Unused VL7 VR7 VL6 VR6 Unused General purpose data memory (same as 8-Bit MCU) Memory Map (1DH~FFH) Register Note: 3/4 No function, read only, read as 0. Unused: No function, read only, read as 0.
* CH1~CH0 channel number selection
D6 DA14 DA6 3/4 FR BL2 FR6 ST14 ST6
D5 DA13 DA5 3/4
D4 DA12 DA4 3/4
D3 DA11 DA3 3/4
D2 DA10 DA2
D1 DA9 DA1
D0 DA8 DA0 SELW Right CH0 FR8 FR0 ST8 ST0 RE8 RE0 VR8
1FH
Left
DAON
20H 21H 22H 23H 24H 25H 26H 27H 28H 29H 2AH 2BH~2FH
CH1 BL1 FR5 ST13 ST5 BL0 FR4 ST12 ST4 RE12 FR11 FR3 ST11 ST3 RE11 RE3 FR10 FR2 ST10 ST2 RE10 RE2 FR9 FR1 ST9 ST1 RE9 RE1 VR9
RE6
RE5 VL9
RE4 VL8
VL5 VR5
VL4 VR4
VL3 VR3
VL2 VR2
VL1 VR1
VL0 VR0
30H~FFH Data memory (RAM)
The HT36FA has a built-in 8 output channels and CH1~CH0 is used to define which channel is selected. When this register is written to, the wavetable synthesizer will automatically output the dedicated PCM code. So this register is also used as a start playing key and it has to be written to after all the other wavetable function registers are already defined.
* Change parameter selection
register will be updated on this selected channel. There are two modes that can be selected to reduce the process of setting the register. Please refer to the statements of the following table: VM 0 0 1 FR 0 1 0 Function Update all the parameter Only update the frequency number Only update the volume
These two bits, VM and FR, are used to define which Rev. 1.10 14 March 13, 2006
HT36FA
* Output frequency definition * Repeat number definition
The data on BL3~BL0 and FR11~FR0 are used to define the output speed of the PCM file, i.e. it can be used to generate the tone scale. When the FR11~FR0 is 800H and BL3~BL0 is 6H, each sample data of the PCM code will be sent out sequentially. When the fOSC is 6.4MHz, the formula of a tone frequency is: 25kHz FR11 ~ FR0 fOUT= fRECORD x x (17 - BL3~BL0) SR 2 where fOUT is the output signal frequency, fRECORD and SR is the frequency and sampling rate on the sample code, respectively. So if a voice code of C3 has been recorded which has the fRECORD of 261Hz and the SR of 11025Hz, the tone frequency (fOUT) of G3: fOUT=98Hz. Can be obtained by using the fomula: 25kHz FR11 ~ FR0 98Hz= 261Hz x x 11025Hz 2 (17 - BL3~BL0) A pair of the values FR11~FR0 and BL3~BL0 can be determined when the fOSC is 6.4MHz.
* Start address definition
The repeat number is used to define the address which is the repeat point of the sample. When the repeat number is defined, it will be output from the start code to the end code once and always output the range between the repeat address to the end code (80H) until the volume become close. The RE12~RE0 is used to calculate the repeat address of the PCM code. The process for setting the RE12~RE0 is to write the 2s complement of the repeat length to RE12~RE0, with the highest carry ignored. The HT36FA will get the repeat address by adding the RE12~RE0 to the address of the end code, then jump to the address to repeat this range.
* Volume control
The HT36FA provides the volume control independently. The volume are controlled by VR9~VR0, respectively. The chip provides 1024 levels of controllable volume, the 000H is the maximum and 3FFH is the minimum output volume.
* The PCM code definition
The HT36FA provides two address types for extended use, one is the program ROM address which is program counter corresponding with PF value, the other is the start address of the PCM code. The ST15~ST0 is used to define the start address of each PCM code and reads the waveform data from this location. The HT36FA provides 16 input data lines from WA17~WA0, the ST15~ST0 is used to locate the major 12 bits .e. WA17~WA5 and the undefined data from WA4~WA0 is always set as 00000b. In other words, the WA17~WA0=ST15~ST025. So each PCM code has to be located at a multiple of 32. Otherwise, the PCM code will not be read out correctly because it has a wrong start code.
* Waveform format definition
The HT36FA can only solve the voice format of the signed 8-bit or 12-bit raw PCM. And the MCU will take the voice code 80H as the end code. So each PCM code section must be ended with the end code 80H.
* Digital to Analog Converter - DAC
The HT36FA accepts two waveform formats to ensure a more economical data space. WBS is used to define the sample format of each PCM code.

WBS=0 means the sample format is 8-bit WBS=1 means the sample format is 12-bit
The HT36FA provides one 16-bit voltage type DAC device controlled by the MCU or Wavetable Synthesizer for driving the external speaker through an external NPN transistor. It is in fact an optional object used for Wavetable Synthesizer DAC or general DAC, this is chosen by Mask Option and DAC control register. If the general DAC is chosen for application, then the Wavetable Synthesizer is disabled since the DAC is taken up and controlled by the MCU. If general DAC is selected, the programmer must write the voice data to register DAL and DAH to get the corresponding analog data. If Mask Option enables the DAC register and the SELW, then the following table comes useful. Bit No. Bit7~Bit3 Label 3/4 SELWL No used SELWL=1, left channel DAC data from wavetable SELWL=0, left channel DAC data from MCU (Default) DAON=1: DAC ON DAON=0: DAC OFF (Default) Function
The 12-bit sample format allocates location to each sample data. Please refer to the waveform format statement as shown below.
8 - B it 1B 2B 3B 4B 5B 6B 7B 8B
Bit2
A s a m p lin g d a ta c o d e ; B m e a n s o n e d a ta b y te . 1 2 - B it 1H 1M 1L 2L 2H 2M 3H 3M 3L
Bit1
DAON
A s a m p lin g d a ta c o d e N o te : " 1 H " H ig h N ib b le " 1 M " M id d le N ib b le " 1 L " L o w N ib b le
Bit0
SELWR=1, Right Channel DAC data from Wavetable SELWR SELWR=0, Right Channel DAC data from MCU (Default)
Waveform Format Rev. 1.10 15 March 13, 2006
HT36FA
Mask Option No. 1 2 3 4 5 6 7 Mask Option WDT source Wake-up Pull-High OSC mode LVR LVD Function On-chip RC/Instruction clock/ disable WDT PA only PA, PB, PC input Crystal or Resistor type Enable/disable 2.2V/3.3V
CLRWDT times One time, two times (CLR WDT1/WDT2)
Application Circuit
V
DD
10W VDD OSC1 OSC2 V 47mF LCH 20kW 0 .1 m F 2 IN 8 VDD 1 VSS 4 5 CE V V 100kW RES 0 .1 m F H T36FA V
DD DD
VDDA
47mF
0 .1 m F
DD
OUTN 7 OUTP SPK 8W
10mF
V re f 3
H T82V733
DD
47mF RCH 20kW VSSA VSS 0 .1 m F 2 IN 8 VDD 1 VSS 4 5 CE 7 OUTP H T82V733 OUTN SPK 8W
10mF
V re f 3
10W VDD OSC1 6M H z OSC2 LCH R1 1kW R2 750W VDDA 47mF 0 .1 m F V
DD
SPK 8W
V V 100kW RES 0 .1 m F
DD
DD
RCH VSSA VSS
R1 1kW R2 750W
SPK 8W
H T36FA N o te : R 1 > R 2
Rev. 1.10
16
March 13, 2006
HT36FA
Instruction Set Summary
Mnemonic Arithmetic ADD A,[m] ADDM A,[m] ADD A,x ADC A,[m] ADCM A,[m] SUB A,x SUB A,[m] SUBM A,[m] SBC A,[m] SBCM A,[m] DAA [m] Add data memory to ACC Add ACC to data memory Add immediate data to ACC Add data memory to ACC with carry Add ACC to data memory with carry Subtract immediate data from ACC Subtract data memory from ACC Subtract data memory from ACC with result in data memory Subtract data memory from ACC with carry Subtract data memory from ACC with carry and result in data memory Decimal adjust ACC for addition with result in data memory 1 1(1) 1 1 1(1) 1 1 1(1) 1 1(1) 1(1) Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV Z,C,AC,OV C Description Instruction Cycle Flag Affected
Logic Operation AND A,[m] OR A,[m] XOR A,[m] ANDM A,[m] ORM A,[m] XORM A,[m] AND A,x OR A,x XOR A,x CPL [m] CPLA [m] AND data memory to ACC OR data memory to ACC Exclusive-OR data memory to ACC AND ACC to data memory OR ACC to data memory Exclusive-OR ACC to data memory AND immediate data to ACC OR immediate data to ACC Exclusive-OR immediate data to ACC Complement data memory Complement data memory with result in ACC 1 1 1 1(1) 1(1) 1(1) 1 1 1 1(1) 1 Z Z Z Z Z Z Z Z Z Z Z
Increment & Decrement INCA [m] INC [m] DECA [m] DEC [m] Rotate RRA [m] RR [m] RRCA [m] RRC [m] RLA [m] RL [m] RLCA [m] RLC [m] Data Move MOV A,[m] MOV [m],A MOV A,x Bit Operation CLR [m].i SET [m].i Clear bit of data memory Set bit of data memory 1(1) 1(1) None None Move data memory to ACC Move ACC to data memory Move immediate data to ACC 1 1(1) 1 None None None Rotate data memory right with result in ACC Rotate data memory right Rotate data memory right through carry with result in ACC Rotate data memory right through carry Rotate data memory left with result in ACC Rotate data memory left Rotate data memory left through carry with result in ACC Rotate data memory left through carry 1 1(1) 1 1(1) 1 1(1) 1 1(1) None None C C None None C C Increment data memory with result in ACC Increment data memory Decrement data memory with result in ACC Decrement data memory 1 1(1) 1 1(1) Z Z Z Z
Rev. 1.10
17
March 13, 2006
HT36FA
Mnemonic Branch JMP addr SZ [m] SZA [m] SZ [m].i SNZ [m].i SIZ [m] SDZ [m] SIZA [m] SDZA [m] CALL addr RET RET A,x RETI Table Read TABRDC [m] TABRDL [m] Miscellaneous NOP CLR [m] SET [m] CLR WDT CLR WDT1 CLR WDT2 SWAP [m] SWAPA [m] HALT Note: No operation Clear data memory Set data memory Clear Watchdog Timer Pre-clear Watchdog Timer Pre-clear Watchdog Timer Swap nibbles of data memory Swap nibbles of data memory with result in Enter Power Down Mode 1 1(1) 1(1) 1 1 1 1(1) 1 1 None None None TO,PDF TO(4),PDF(4) TO(4),PDF(4) None None TO,PDF Read ROM code (current page) to data memory and TBLH Read ROM code (last page) to data memory and TBLH 2(1) 2(1) None None Jump unconditionally Skip if data memory is zero Skip if data memory is zero with data movement to ACC Skip if bit i of data memory is zero Skip if bit i of data memory is not zero Skip if increment data memory is zero Skip if decrement data memory is zero Skip if increment data memory is zero with result in ACC Skip if decrement data memory is zero with result in ACC Subroutine call Return from subroutine Return from subroutine and load immediate data to ACC Return from interrupt 2 1(2) 1(2) 1(2) 1(2) 1(3) 1(3) 1(2) 1(2) 2 2 2 2 None None None None None None None None None None None None None Description Instruction Cycle Flag Affected
x: Immediate data m: Data memory address A: Accumulator i: 0~7 number of bits addr: Program memory address O: Flag is affected -: Flag is not affected
(1)
: If a loading to the PCL register occurs, the execution cycle of instructions will be delayed for one more cycle (four system clocks). : If a skipping to the next instruction occurs, the execution cycle of instructions will be delayed for one more cycle (four system clocks). Otherwise the original instruction cycle is unchanged. : and (2)
(2)
(3) (1) (4)
: The flags may be affected by the execution status. If the Watchdog Timer is cleared by executing the CLR WDT1 or CLR WDT2 instruction, the TO and PDF are cleared. Otherwise the TO and PDF flags remain unchanged.
Rev. 1.10
18
March 13, 2006
HT36FA
Instruction Definition
ADC A,[m] Description Operation Affected flag(s) TO 3/4 ADCM A,[m] Description Operation Affected flag(s) TO 3/4 ADD A,[m] Description Operation Affected flag(s) TO 3/4 ADD A,x Description Operation Affected flag(s) TO 3/4 ADDM A,[m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O Add data memory and carry to the accumulator The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator. ACC ACC+[m]+C
Add the accumulator and carry to data memory The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory. [m] ACC+[m]+C
Add data memory to the accumulator The contents of the specified data memory and the accumulator are added. The result is stored in the accumulator. ACC ACC+[m]
Add immediate data to the accumulator The contents of the accumulator and the specified data are added, leaving the result in the accumulator. ACC ACC+x
Add the accumulator to the data memory The contents of the specified data memory and the accumulator are added. The result is stored in the data memory. [m] ACC+[m]
Rev. 1.10
19
March 13, 2006
HT36FA
AND A,[m] Description Operation Affected flag(s) TO 3/4 AND A,x Description Operation Affected flag(s) TO 3/4 ANDM A,[m] Description Operation Affected flag(s) TO 3/4 CALL addr Description PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 Logical AND accumulator with data memory Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator. ACC ACC AND [m]
Logical AND immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical_AND operation. The result is stored in the accumulator. ACC ACC AND x
Logical AND data memory with the accumulator Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory. [m] ACC AND [m]
Subroutine call The instruction unconditionally calls a subroutine located at the indicated address. The program counter increments once to obtain the address of the next instruction, and pushes this onto the stack. The indicated address is then loaded. Program execution continues with the instruction at this address. Stack Program Counter+1 Program Counter addr
Operation Affected flag(s)
TO 3/4 CLR [m] Description Operation Affected flag(s) TO 3/4
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Clear data memory The contents of the specified data memory are cleared to 0. [m] 00H
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.10
20
March 13, 2006
HT36FA
CLR [m].i Description Operation Affected flag(s) TO 3/4 CLR WDT Description Operation Affected flag(s) TO 0 CLR WDT1 Description PDF 0 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Clear bit of data memory The bit i of the specified data memory is cleared to 0. [m].i 0
Clear Watchdog Timer The WDT is cleared (clears the WDT). The power down bit (PDF) and time-out bit (TO) are cleared. WDT 00H PDF and TO 0
Preclear Watchdog Timer Together with CLR WDT2, clears the WDT. PDF and TO are also cleared. Only execution of this instruction without the other preclear instruction just sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged. WDT 00H* PDF and TO 0*
Operation Affected flag(s)
TO 0* CLR WDT2 Description
PDF 0*
OV 3/4
Z 3/4
AC 3/4
C 3/4
Preclear Watchdog Timer Together with CLR WDT1, clears the WDT. PDF and TO are also cleared. Only execution of this instruction without the other preclear instruction, sets the indicated flag which implies this instruction has been executed and the TO and PDF flags remain unchanged. WDT 00H* PDF and TO 0*
Operation Affected flag(s)
TO 0* CPL [m] Description Operation Affected flag(s) TO 3/4
PDF 0*
OV 3/4
Z 3/4
AC 3/4
C 3/4
Complement data memory Each bit of the specified data memory is logically complemented (1s complement). Bits which previously contained a 1 are changed to 0 and vice-versa. [m] [m]
PDF 3/4
OV 3/4
Z O
AC 3/4
C 3/4
Rev. 1.10
21
March 13, 2006
HT36FA
CPLA [m] Description Complement data memory and place result in the accumulator Each bit of the specified data memory is logically complemented (1s complement). Bits which previously contained a 1 are changed to 0 and vice-versa. The complemented result is stored in the accumulator and the contents of the data memory remain unchanged. ACC [m]
Operation Affected flag(s)
TO 3/4 DAA [m] Description
PDF 3/4
OV 3/4
Z O
AC 3/4
C 3/4
Decimal-Adjust accumulator for addition The accumulator value is adjusted to the BCD (Binary Coded Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored in the data memory and only the carry flag (C) may be affected. If ACC.3~ACC.0 >9 or AC=1 then [m].3~[m].0 (ACC.3~ACC.0)+6, AC1=AC else [m].3~[m].0 (ACC.3~ACC.0), AC1=0 and If ACC.7~ACC.4+AC1 >9 or C=1 then [m].7~[m].4 ACC.7~ACC.4+6+AC1,C=1 else [m].7~[m].4 ACC.7~ACC.4+AC1,C=C
Operation
Affected flag(s) TO 3/4 DEC [m] Description Operation Affected flag(s) TO 3/4 DECA [m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Decrement data memory Data in the specified data memory is decremented by 1. [m] [m]-1
Decrement data memory and place result in the accumulator Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged. ACC [m]-1
Rev. 1.10
22
March 13, 2006
HT36FA
HALT Description Enter Power Down Mode This instruction stops program execution and turns off the system clock. The contents of the RAM and registers are retained. The WDT and prescaler are cleared. The power down bit (PDF) is set and the WDT time-out bit (TO) is cleared. Program Counter Program Counter+1 PDF 1 TO 0
Operation
Affected flag(s) TO 0 INC [m] Description Operation Affected flag(s) TO 3/4 INCA [m] Description Operation Affected flag(s) TO 3/4 JMP addr Description Operation Affected flag(s) TO 3/4 MOV A,[m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Directly jump The program counter are replaced with the directly-specified address unconditionally, and control is passed to this destination. Program Counter addr PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 1 OV 3/4 Z 3/4 AC 3/4 C 3/4
Increment data memory Data in the specified data memory is incremented by 1 [m] [m]+1
Increment data memory and place result in the accumulator Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged. ACC [m]+1
Move data memory to the accumulator The contents of the specified data memory are copied to the accumulator. ACC [m]
Rev. 1.10
23
March 13, 2006
HT36FA
MOV A,x Description Operation Affected flag(s) TO 3/4 MOV [m],A Description Operation Affected flag(s) TO 3/4 NOP Description Operation Affected flag(s) TO 3/4 OR A,[m] Description Operation Affected flag(s) TO 3/4 OR A,x Description Operation Affected flag(s) TO 3/4 ORM A,[m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 No operation No operation is performed. Execution continues with the next instruction. Program Counter Program Counter+1 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Move immediate data to the accumulator The 8-bit data specified by the code is loaded into the accumulator. ACC x
Move the accumulator to data memory The contents of the accumulator are copied to the specified data memory (one of the data memories). [m] ACC
Logical OR accumulator with data memory Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator. ACC ACC OR [m]
Logical OR immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical_OR operation. The result is stored in the accumulator. ACC ACC OR x
Logical OR data memory with the accumulator Data in the data memory (one of the data memories) and the accumulator perform a bitwise logical_OR operation. The result is stored in the data memory. [m] ACC OR [m]
Rev. 1.10
24
March 13, 2006
HT36FA
RET Description Operation Affected flag(s) TO 3/4 RET A,x Description Operation Affected flag(s) TO 3/4 RETI Description Operation Affected flag(s) TO 3/4 RL [m] Description Operation Affected flag(s) TO 3/4 RLA [m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Return from subroutine The program counter is restored from the stack. This is a 2-cycle instruction. Program Counter Stack
Return and place immediate data in the accumulator The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data. Program Counter Stack ACC x
Return from interrupt The program counter is restored from the stack, and interrupts are enabled by setting the EMI bit. EMI is the enable master (global) interrupt bit. Program Counter Stack EMI 1
Rotate data memory left The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0. [m].(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) [m].0 [m].7
Rotate data memory left and place result in the accumulator Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the rotated result in the accumulator. The contents of the data memory remain unchanged. ACC.(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) ACC.0 [m].7
Rev. 1.10
25
March 13, 2006
HT36FA
RLC [m] Description Operation Rotate data memory left through carry The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position. [m].(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) [m].0 C C [m].7
Affected flag(s) TO 3/4 RLCA [m] Description PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Rotate left through carry and place result in the accumulator Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored in the accumulator but the contents of the data memory remain unchanged. ACC.(i+1) [m].i; [m].i:bit i of the data memory (i=0~6) ACC.0 C C [m].7
Operation
Affected flag(s) TO 3/4 RR [m] Description Operation Affected flag(s) TO 3/4 RRA [m] Description Operation Affected flag(s) TO 3/4 RRC [m] Description Operation PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Rotate data memory right The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7. [m].i [m].(i+1); [m].i:bit i of the data memory (i=0~6) [m].7 [m].0
Rotate right and place result in the accumulator Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving the rotated result in the accumulator. The contents of the data memory remain unchanged. ACC.(i) [m].(i+1); [m].i:bit i of the data memory (i=0~6) ACC.7 [m].0
Rotate data memory right through carry The contents of the specified data memory and the carry flag are together rotated 1 bit right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position. [m].i [m].(i+1); [m].i:bit i of the data memory (i=0~6) [m].7 C C [m].0
Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Rev. 1.10
26
March 13, 2006
HT36FA
RRCA [m] Description Rotate right through carry and place result in the accumulator Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is stored in the accumulator. The contents of the data memory remain unchanged. ACC.i [m].(i+1); [m].i:bit i of the data memory (i=0~6) ACC.7 C C [m].0
Operation
Affected flag(s) TO 3/4 SBC A,[m] Description Operation Affected flag(s) TO 3/4 SBCM A,[m] Description Operation Affected flag(s) TO 3/4 SDZ [m] Description PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C O
Subtract data memory and carry from the accumulator The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the accumulator. ACC ACC+[m]+C
Subtract data memory and carry from the accumulator The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory. [m] ACC+[m]+C
Skip if decrement data memory is 0 The contents of the specified data memory are decremented by 1. If the result is 0, the next instruction is skipped. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]-1)=0, [m] ([m]-1)
Operation Affected flag(s)
TO 3/4 SDZA [m] Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Decrement data memory and place result in ACC, skip if 0 The contents of the specified data memory are decremented by 1. If the result is 0, the next instruction is skipped. The result is stored in the accumulator but the data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]-1)=0, ACC ([m]-1)
Operation Affected flag(s)
TO 3/4
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.10
27
March 13, 2006
HT36FA
SET [m] Description Operation Affected flag(s) TO 3/4 SET [m]. i Description Operation Affected flag(s) TO 3/4 SIZ [m] Description PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 Set data memory Each bit of the specified data memory is set to 1. [m] FFH
Set bit of data memory Bit i of the specified data memory is set to 1. [m].i 1
Skip if increment data memory is 0 The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]+1)=0, [m] ([m]+1)
Operation Affected flag(s)
TO 3/4 SIZA [m] Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Increment data memory and place result in ACC, skip if 0 The contents of the specified data memory are incremented by 1. If the result is 0, the next instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if ([m]+1)=0, ACC ([m]+1)
Operation Affected flag(s)
TO 3/4 SNZ [m].i Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Skip if bit i of the data memory is not 0 If bit i of the specified data memory is not 0, the next instruction is skipped. If bit i of the data memory is not 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m].i0
Operation Affected flag(s)
TO 3/4
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.10
28
March 13, 2006
HT36FA
SUB A,[m] Description Operation Affected flag(s) TO 3/4 SUBM A,[m] Description Operation Affected flag(s) TO 3/4 SUB A,x Description Operation Affected flag(s) TO 3/4 SWAP [m] Description Operation Affected flag(s) TO 3/4 SWAPA [m] Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z 3/4 AC 3/4 C 3/4 PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O PDF 3/4 OV O Z O AC O C O Subtract data memory from the accumulator The specified data memory is subtracted from the contents of the accumulator, leaving the result in the accumulator. ACC ACC+[m]+1
Subtract data memory from the accumulator The specified data memory is subtracted from the contents of the accumulator, leaving the result in the data memory. [m] ACC+[m]+1
Subtract immediate data from the accumulator The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator. ACC ACC+x+1
Swap nibbles within the data memory The low-order and high-order nibbles of the specified data memory (1 of the data memories) are interchanged. [m].3~[m].0 [m].7~[m].4
Swap data memory and place result in the accumulator The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged. ACC.3~ACC.0 [m].7~[m].4 ACC.7~ACC.4 [m].3~[m].0
Rev. 1.10
29
March 13, 2006
HT36FA
SZ [m] Description Skip if data memory is 0 If the contents of the specified data memory are 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m]=0
Operation Affected flag(s)
TO 3/4 SZA [m] Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move data memory to ACC, skip if 0 The contents of the specified data memory are copied to the accumulator. If the contents is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m]=0
Operation Affected flag(s)
TO 3/4 SZ [m].i Description
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Skip if bit i of the data memory is 0 If bit i of the specified data memory is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle). Skip if [m].i=0
Operation Affected flag(s)
TO 3/4 TABRDC [m] Description Operation Affected flag(s) TO 3/4 TABRDL [m] Description Operation Affected flag(s) TO 3/4
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move the ROM code (current page) to TBLH and data memory The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved to the specified data memory and the high byte transferred to TBLH directly. [m] ROM code (low byte) TBLH ROM code (high byte)
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Move the ROM code (last page) to TBLH and data memory The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to the data memory and the high byte transferred to TBLH directly. [m] ROM code (low byte) TBLH ROM code (high byte)
PDF 3/4
OV 3/4
Z 3/4
AC 3/4
C 3/4
Rev. 1.10
30
March 13, 2006
HT36FA
XOR A,[m] Description Operation Affected flag(s) TO 3/4 XORM A,[m] Description Operation Affected flag(s) TO 3/4 XOR A,x Description Operation Affected flag(s) TO 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 PDF 3/4 OV 3/4 Z O AC 3/4 C 3/4 Logical XOR accumulator with data memory Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator. ACC ACC XOR [m]
Logical XOR data memory with the accumulator Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected. [m] ACC XOR [m]
Logical XOR immediate data to the accumulator Data in the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected. ACC ACC XOR x
Rev. 1.10
31
March 13, 2006
HT36FA
Package Information
20-pin SOP (300mil) Outline Dimensions
20
A
11
B
1
C C'
10
G H
D E F
a
Symbol A B C C D E F G H a
Dimensions in mil Min. 394 290 14 490 92 3/4 4 32 4 0 Nom. 3/4 3/4 3/4 3/4 3/4 50 3/4 3/4 3/4 3/4 Max. 419 300 20 510 104 3/4 3/4 38 12 10
Rev. 1.10
32
March 13, 2006
HT36FA
32-pin SOP (450mil) Outline Dimensions
32 A
17 B
1
16
C C' G H D E F
a
Symbol A B C C D E F G H a
Dimensions in mil Min. 543 440 14 3/4 100 3/4 4 32 4 0 Nom. 3/4 3/4 3/4 3/4 3/4 50 3/4 3/4 3/4 3/4 Max. 557 450 20 817 112 3/4 3/4 38 12 10
Rev. 1.10
33
March 13, 2006
HT36FA
Product Tape and Reel Specifications
Reel Dimensions
T2 D
A
B
C
T1
SOP 20W Symbol A B C D T1 T2 Description Reel Outer Diameter Reel Inner Diameter Spindle Hole Diameter Key Slit Width Space Between Flange Reel Thickness Dimensions in mm 3301 621.5 13+0.5 -0.2 20.5 24.8+0.3 -0.2 30.20.2
SOP 32W Symbol A B C D T1 T2 Description Reel Outer Diameter Reel Inner Diameter Spindle Hole Diameter Key Slit Width Space Between Flange Reel Thickness Dimensions in mm 3301 1000.1 13+0.5 -0.2 20.5 32.8+0.3 -0.2 38.2+0.2
Rev. 1.10
34
March 13, 2006
HT36FA
Carrier Tape Dimensions
D
E F
P0
P1
t
W C
B0
D1
P
K0 A0
SOP 20W Symbol W P E F D D1 P0 P1 A0 B0 K0 t C Description Carrier Tape Width Cavity Pitch Perforation Position Cavity to Perforation (Width Direction) Perforation Diameter Cavity Hole Diameter Perforation Pitch Cavity to Perforation (Length Direction) Cavity Length Cavity Width Cavity Depth Carrier Tape Thickness Cover Tape Width Dimensions in mm 24+0.3 -0.1 120.1 1.750.1 11.50.1 1.5+0.1 1.5+0.25 40.1 20.1 10.80.1 13.30.1 3.20.1 0.30.05 21.3
Rev. 1.10
35
March 13, 2006
HT36FA
D
E F W C B0
P0
P1
t
D1
P K2 A0
K1
SOP 32W Symbol W P E F D D1 P0 P1 A0 B0 K1 K2 t C Description Carrier Tape Width Cavity Pitch Perforation Position Cavity to Perforation (Width Direction) Perforation Diameter Cavity Hole Diameter Perforation Pitch Cavity to Perforation (Length Direction) Cavity Length Cavity Width Cavity Depth Cavity Depth Carrier Tape Thickness Cover Tape Width Dimensions in mm 32+0.3 -0.1 160.1 1.750.1 14.20.1 1.55+0.1 2+0.25 40.1 20.1 14.70.1 20.90.1 30.1 3.40.1 0.350.05 25.5
Rev. 1.10
36
March 13, 2006
HT36FA
Holtek Semiconductor Inc. (Headquarters) No.3, Creation Rd. II, Science Park, Hsinchu, Taiwan Tel: 886-3-563-1999 Fax: 886-3-563-1189 http://www.holtek.com.tw Holtek Semiconductor Inc. (Taipei Sales Office) 4F-2, No. 3-2, YuanQu St., Nankang Software Park, Taipei 115, Taiwan Tel: 886-2-2655-7070 Fax: 886-2-2655-7373 Fax: 886-2-2655-7383 (International sales hotline) Holtek Semiconductor Inc. (Shanghai Sales Office) 7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China 200233 Tel: 021-6485-5560 Fax: 021-6485-0313 http://www.holtek.com.cn Holtek Semiconductor Inc. (Shenzhen Sales Office) 43F, SEG Plaza, Shen Nan Zhong Road, Shenzhen, China 518031 Tel: 0755-8346-5589 Fax: 0755-8346-5590 ISDN: 0755-8346-5591 Holtek Semiconductor Inc. (Beijing Sales Office) Suite 1721, Jinyu Tower, A129 West Xuan Wu Men Street, Xicheng District, Beijing, China 100031 Tel: 010-6641-0030, 6641-7751, 6641-7752 Fax: 010-6641-0125 Holmate Semiconductor, Inc. (North America Sales Office) 46712 Fremont Blvd., Fremont, CA 94538 Tel: 510-252-9880 Fax: 510-252-9885 http://www.holmate.com Copyright O 2006 by HOLTEK SEMICONDUCTOR INC. The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable without further modification, nor recommends the use of its products for application that may present a risk to human life due to malfunction or otherwise. Holteks products are not authorized for use as critical components in life support devices or systems. Holtek reserves the right to alter its products without prior notification. For the most up-to-date information, please visit our web site at http://www.holtek.com.tw.
Rev. 1.10
37
March 13, 2006

▲Up To Search▲

Price & Availability of HT36FA

	To Download HT36FA Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .